File content as of revision 73:f6f378311c8d:

#include "mbed.h"
#include "StaticDefs.hpp"

#ifndef lround
#define lround(var)    (long)(var+0.5f)
#endif

////////////////////////////////////////////////////////////////// NEW TICKER
Ticker systemTicker;
bool setup_complete = false;
volatile unsigned int bTick = 0;
volatile unsigned int timer_counter = 0;

static unsigned int read_ticker(void) {      //Basically this makes sure you're reading the data at one instance (not while it's changing)
    unsigned int val = bTick;
    if( val )
        bTick = 0;
    return( val );
}
////////////////////////////////////////////////////////////////// NEW TICKER
 
// loop rate used to determine how fast events trigger in the while loop
//Ticker main_loop_rate_ticker;
//Ticker log_loop_rate_ticker;

volatile bool fsm_loop = false; //used so the compiler does not optimize this variable (load from memory, do not assume state of variable)
volatile bool log_loop = false; //used so the compiler does not optimize this variable (load from memory, do not assume state of variable)

void loop_trigger() { fsm_loop = true;} // loop trigger (used in while loop)
void log_loop_trigger() { log_loop = true;} // log loop trigger (used in while loop)

static int current_state = 0;     
static bool file_opened = false;

void FSM() {                    // FSM loop runs at 10 hz
    if(fsm_loop) {
        // led one removed
        fsm_loop = false;       // wait until the loop rate timer fires again
        current_state = stateMachine().runStateMachine();       //running State Machine. Returns 0 if sitting idle or keyboard press (SIT_IDLE state).
    }
}

void log_function() {    
    // log loop runs at 1 hz
    if (log_loop) {
        //when the state machine is not in SIT_IDLE state (or a random keyboard press)

        //if (current_state == TRANSMIT_MBED_LOG or current_state == RECEIVE_SEQUENCE) {                
//            ;   //pass
//        }
        
        if(current_state != 0) {
            if (!file_opened) {                                 //if the log file is not open, open it
                mbedLogger().appendLogFile(current_state, 0);   //open MBED file once
                //sdLogger().appendLogFile(current_state, 0);     //open SD file once
                           
                file_opened = true;                             //stops it from continuing to open it

                pc().printf(">>>>>>>> Recording. Log file opened. <<<<<<<<\n\r");
            }
            
            //record to Mbed file system   
            
            mbedLogger().appendLogFile(current_state, 1);    //writing data
            //sdLogger().appendLogFile(current_state, 1);    //writing data
        }
        
        //when the current FSM state is zero (SIT_IDLE), close the file
        else {
            //this can only happen once
            if (file_opened) {
                //WRITE ONCE
                mbedLogger().appendLogFile(current_state, 1);   //write the idle state, then close
                
                mbedLogger().appendLogFile(current_state, 0);    //close log file
                //sdLogger().appendLogFile(current_state, 0);    //close log file
                
                file_opened = false;
                
                pc().printf(">>>>>>>> Stopped recording. Log file closed. <<<<<<<<\n\r");
            }
        }
    }   //END OF LOG LOOP
    
    log_loop = false;   // wait until the loop rate timer fires again
}

//single system timer to run hardware/electronics timing
static void system_timer(void) {
    bTick = 1;
    
    timer_counter++;
    
    //only start these updates when everything is properly setup (through setup function)
    if (setup_complete) {
        if ( (timer_counter % 1) == 0) {    //this runs at 0.001 second intervals (1000 Hz)
            adc().update();  //every iteration of this the A/D converter runs   //now this runs at 0.01 second intervals 03/12/2018
        }
        
        if ( (timer_counter % 10) == 0) {
            bce().update();      //update() inside LinearActuator class (running at 0.01 second intervals)
            batt().update();
        }
        
        if ( (timer_counter % 20) == 0 ) {    // 0.02 second intervals
            //rudder().runServo();
        }
        
        if ( (timer_counter % 50) == 0 ) {    // 0.05 second intervals 
            imu().runIMU();
        }
                
        if ( (timer_counter % 100) == 0) {     // 100,000 microseconds = 0.1 second intervals
            depthLoop().runOuterLoop();
            pitchLoop().runOuterLoop();
            headingLoop().runOuterLoop();
        }
        
        if ( (timer_counter % 1000) == 0) {        // update at 1.0 second intervals
            //gui().updateGUI();
        }
    }
}

void setup() {
    pc().baud(57600);
    pc().printf("\n\n\r FSG PCB Bench Test version 1.7C)\n\n\r");
 
    // start up the system timer
    //systemTimer().start();
 
    // set up and start the adc. This runs on a fixed interval and is interrupt driven
    adc().initialize();
    //one central interrupt is updating the ADC (not using the start function)
    
    // setup and run the rudder(servo) pwm signal (start the ticker)
    //rudder().init();
    pc().printf("Rudder servo initialized!\n\r");
    
    // set up and start the imu. This polls in the background
    imu().initialize();
    //imu().start();
    
    // construct the MBED local file system
    local();
    
    // construct the SD card file system
    //sd_card();
 
    // load config data from files
    configFileIO().load_BCE_config();       // load the buoyancy engine parameters from the file "bce.txt"
    configFileIO().load_BATT_config();      // load the battery mass mover parameters from the file "batt.txt"
    
    configFileIO().load_DEPTH_config();     // load the depth control loop parameters from the file "depth.txt" (contains neutral position)
    configFileIO().load_PITCH_config();     // load the depth control loop parameters from the file "pitch.txt" (contains neutral position)
    
    configFileIO().load_RUDDER_config();    // load the rudder servo inner loop parameters from the file "SERVO.txt"
    configFileIO().load_HEADING_config();   // load the rudder servo outer loop HEADING control parameters from the file "HEADING.txt" (contains neutral position)
 
    // set up the linear actuators.  adc has to be running first.
    bce().setPIDHighLimit(bce().getTravelLimit());     //travel limit of this linear actuator
    bce().init();
    //bce().start();  //removed start, it's handled by the interrupt
    bce().runLinearActuator();
    bce().pause(); // start by not moving
 
    batt().setPIDHighLimit(batt().getTravelLimit());    //travel limit of this linear actuator
    batt().init();
    batt().runLinearActuator(); // _init = true;
    //batt().start();//removed start, it's handled by the interrupt
    batt().pause(); // start by not moving
 
    // set up the depth, pitch, and rudder outer loop controllers
    depthLoop().init();
    //removed start, it's handled by the interrupt
    depthLoop().setCommand(stateMachine().getDepthCommand());
 
    pitchLoop().init();
    //removed start, it's handled by the interrupt
    pitchLoop().setCommand(stateMachine().getPitchCommand());
    
    headingLoop().init();           
    //removed start, it's handled by the interrupt
    //headingLoop().setCommand(stateMachine().getHeadingCommand());         // FIX LATER
    //heading flag that adjust the PID error is set in the constructor
    
    //systemTicker.attach_us(&system_timer, 10000);         // Interrupt timer running at 0.01 seconds       (slower than original ADC time interval)
    
    
 
    // show that the PID gains are loading from the file
    pc().printf("bce    P:%6.2f, I:%6.2f, D:%6.2f, zero %3i, limit %6.1f mm, slope %0.5f  \r\n", bce().getControllerP(), bce().getControllerI(), bce().getControllerD(), bce().getZeroCounts(), bce().getTravelLimit(), bce().getPotSlope());
    pc().printf("batt   P:%6.2f, I:%6.2f, D:%6.2f, zero %3i, limit %6.1f mm, slope %0.5f  \r\n", batt().getControllerP(), batt().getControllerI(), batt().getControllerD(), batt().getZeroCounts(), batt().getTravelLimit(), batt().getPotSlope());
    pc().printf("rudder min pwm: %6.2f, max pwm: %6.2f, center pwm: %6.2f, min deg: %6.2f, max deg: %6.2f\r\n", rudder().getMinPWM(), rudder().getMaxPWM(), rudder().getCenterPWM(), rudder().getMinDeg(), rudder().getMaxDeg());
    
    pc().printf("depth   P:%6.2f, I:%6.2f, D:%6.2f, offset:%6.1f mm \r\n", depthLoop().getControllerP(), depthLoop().getControllerI(), depthLoop().getControllerD(), depthLoop().getOutputOffset());
    pc().printf("pitch   P:%6.2f, I:%6.2f, D:%6.2f, offset:%6.1f mm \r\n", pitchLoop().getControllerP(), pitchLoop().getControllerI(), pitchLoop().getControllerD(), pitchLoop().getOutputOffset());
    pc().printf("heading P: %3.2f, I: %3.2f, D %3.2f, offset: %3.1f deg (deadband: %0.1f)\r\n", headingLoop().getControllerP(), headingLoop().getControllerI(), headingLoop().getControllerD(), headingLoop().getOutputOffset(), headingLoop().getDeadband());
    
    pc().printf("\n\r");
         
    //load sequence from file
    sequenceController().loadSequence();
    
    //set time of logger (to current or close-to-current time)
    mbedLogger().setLogTime();
    //sdLogger().setLogTime();
    
    //create log files if not present on file system
    mbedLogger().initializeLogFile();
    //sdLogger().initializeLogFile();
    
    setup_complete = true;    
}

/*************************** v1.8 **************************/

int main() {   
    setup();    //setup electronics/hardware
    
    systemTicker.attach_us(&system_timer, 1000);         // Interrupt timer running at 0.001 seconds       (slower than original ADC time interval)
    
    unsigned int tNow = 0;
    
    //pc().baud(57600);
    pc().printf("\n\n\r FSG PCB v1.8 (XBee) 07/12/2018 \n\n\r");
    
    systemTicker.attach_us(&system_timer, 1000);         // Interrupt timer running at 0.001 seconds       (slower than original ADC time interval)
        
    while (1) {        
        if( read_ticker() )                         // read_ticker runs at the speed of 10 kHz (adc timing)
        {
            ++tNow;

            //run finite state machine fast when transmitting data
            if (current_state == TX_MBED_LOG or current_state == RECEIVE_SEQUENCE) {
                if ( (tNow % 100) == 0 ) {   // 0.01 second intervals  (100 Hz)
                    fsm_loop = true;
                    FSM();
                }
            }
            
            //NOT TRANSMITTING DATA, NORMAL OPERATIONS
            else {  
            //FSM
                if ( (tNow % 100) == 0 ) {   // 0.1 second intervals
                    fsm_loop = true;
                    FSM();
                    
                    //get commands and update GUI
                    gui().getCommandFSM();
                }        
            //LOGGING     
                if ( (tNow % 1000) == 0 ) {   // 1.0 second intervals                
                    log_loop = true;
                    log_function();
                }
            }
        }
    }
}