Websocket_Sample for MurataTypeYD

Dependencies:   mbed picojson

Revision:
0:14bd24b5a77f
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/PowerControl/EthernetPowerControl.cpp	Thu Mar 12 12:14:38 2015 +0000
@@ -0,0 +1,138 @@
+#include "EthernetPowerControl.h"
+
+static void write_PHY (unsigned int PhyReg, unsigned short Value) {
+   /* Write a data 'Value' to PHY register 'PhyReg'. */
+   unsigned int tout;
+   /* Hardware MII Management for LPC176x devices. */
+   LPC_EMAC->MADR = DP83848C_DEF_ADR | PhyReg;
+   LPC_EMAC->MWTD = Value;
+
+   /* Wait utill operation completed */
+   for (tout = 0; tout < MII_WR_TOUT; tout++) {
+      if ((LPC_EMAC->MIND & MIND_BUSY) == 0) {
+         break;
+      }
+   }
+}
+
+static unsigned short read_PHY (unsigned int PhyReg) {
+   /* Read a PHY register 'PhyReg'. */
+   unsigned int tout, val;
+
+   LPC_EMAC->MADR = DP83848C_DEF_ADR | PhyReg;
+   LPC_EMAC->MCMD = MCMD_READ;
+
+   /* Wait until operation completed */
+   for (tout = 0; tout < MII_RD_TOUT; tout++) {
+      if ((LPC_EMAC->MIND & MIND_BUSY) == 0) {
+         break;
+      }
+   }
+   LPC_EMAC->MCMD = 0;
+   val = LPC_EMAC->MRDD;
+   
+   return (val);
+}
+
+void EMAC_Init()
+{
+  unsigned int tout,regv;
+  /* Power Up the EMAC controller. */
+  Peripheral_PowerUp(LPC1768_PCONP_PCENET);
+  
+  LPC_PINCON->PINSEL2 = 0x50150105;
+  LPC_PINCON->PINSEL3 &= ~0x0000000F;
+  LPC_PINCON->PINSEL3 |= 0x00000005;
+
+  /* Reset all EMAC internal modules. */
+  LPC_EMAC->MAC1 = MAC1_RES_TX | MAC1_RES_MCS_TX | MAC1_RES_RX | MAC1_RES_MCS_RX |
+             MAC1_SIM_RES | MAC1_SOFT_RES;
+  LPC_EMAC->Command = CR_REG_RES | CR_TX_RES | CR_RX_RES;
+
+  /* A short delay after reset. */
+  for (tout = 100; tout; tout--);
+
+  /* Initialize MAC control registers. */
+  LPC_EMAC->MAC1 = MAC1_PASS_ALL;
+  LPC_EMAC->MAC2 = MAC2_CRC_EN | MAC2_PAD_EN;
+  LPC_EMAC->MAXF = ETH_MAX_FLEN;
+  LPC_EMAC->CLRT = CLRT_DEF;
+  LPC_EMAC->IPGR = IPGR_DEF;
+
+  /* Enable Reduced MII interface. */
+  LPC_EMAC->Command = CR_RMII | CR_PASS_RUNT_FRM;
+
+  /* Reset Reduced MII Logic. */
+  LPC_EMAC->SUPP = SUPP_RES_RMII;
+  for (tout = 100; tout; tout--);
+  LPC_EMAC->SUPP = 0;
+
+  /* Put the DP83848C in reset mode */
+  write_PHY (PHY_REG_BMCR, 0x8000);
+
+  /* Wait for hardware reset to end. */
+  for (tout = 0; tout < 0x100000; tout++) {
+    regv = read_PHY (PHY_REG_BMCR);
+    if (!(regv & 0x8000)) {
+      /* Reset complete */
+      break;
+    }
+  }
+}
+
+
+void PHY_PowerDown()
+{
+    if (!Peripheral_GetStatus(LPC1768_PCONP_PCENET))
+        EMAC_Init(); //init EMAC if it is not already init'd
+    
+    unsigned int regv;
+    regv = read_PHY(PHY_REG_BMCR);
+    write_PHY(PHY_REG_BMCR, regv | (1 << PHY_REG_BMCR_POWERDOWN));
+    regv = read_PHY(PHY_REG_BMCR);
+    
+    //shouldn't need the EMAC now.
+    Peripheral_PowerDown(LPC1768_PCONP_PCENET);
+    
+    //and turn off the PHY OSC
+     LPC_GPIO1->FIODIR |= 0x8000000;
+     LPC_GPIO1->FIOCLR = 0x8000000;
+}
+
+void PHY_PowerUp()
+{   
+    if (!Peripheral_GetStatus(LPC1768_PCONP_PCENET))
+        EMAC_Init(); //init EMAC if it is not already init'd
+        
+    LPC_GPIO1->FIODIR |= 0x8000000;
+    LPC_GPIO1->FIOSET = 0x8000000;
+    
+    //wait for osc to be stable
+    wait_ms(200);
+    
+    unsigned int regv;
+    regv = read_PHY(PHY_REG_BMCR);
+    write_PHY(PHY_REG_BMCR, regv & ~(1 << PHY_REG_BMCR_POWERDOWN));
+    regv = read_PHY(PHY_REG_BMCR);
+}
+
+void PHY_EnergyDetect_Enable()
+{
+    if (!Peripheral_GetStatus(LPC1768_PCONP_PCENET))
+        EMAC_Init(); //init EMAC if it is not already init'd
+        
+    unsigned int regv;
+    regv = read_PHY(PHY_REG_EDCR);
+    write_PHY(PHY_REG_BMCR, regv | (1 << PHY_REG_EDCR_ENABLE));
+    regv = read_PHY(PHY_REG_EDCR);   
+}
+
+void PHY_EnergyDetect_Disable()
+{
+    if (!Peripheral_GetStatus(LPC1768_PCONP_PCENET))
+        EMAC_Init(); //init EMAC if it is not already init'd
+    unsigned int regv;
+    regv = read_PHY(PHY_REG_EDCR);
+    write_PHY(PHY_REG_BMCR, regv & ~(1 << PHY_REG_EDCR_ENABLE));
+    regv = read_PHY(PHY_REG_EDCR);   
+}
\ No newline at end of file