Diff: main.cpp

Revision:

0:b183e63b31f8

Child:

1:cb8a26c1d6e9

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/main.cpp	Fri Aug 21 11:40:23 2015 +0000
@@ -0,0 +1,59 @@
+/*Data send-receive by IIC-bus Hardware: IIC-board with 4 x PCF8574 IC
+you see a 8bit leds this leds show the value from an other 8574 who has 8 switches as input
+The 8xswitches from IIC you can see also at the pins PC_0 to PC_7
+Tasks: 1. Receive a analog value and show this value as a 8xled-strip at the third PCF8574 IC
+        2. Send the 8xswitches from IIC-bus to the virtuell COM-port. You can visualize the switches
+           with the Software "Profilab" or "LABview"
+Aug. 2015 G. Neumaier Gewerblich-Technische Schule Offenburg Germany
+*/
+
+#include "mbed.h"
+#define PCF8574_ADDRoutput  0x46 // PCF8574 address 0x46 lowest bit (R/W)=0 IICboard P3
+#define PCF8574_ADDRinput   0x45 // PCF8574 address 0x44 lowest bit (R/W)=0 IICboard P2
+        //ADR-Jumper on IIC4xPCF8574board jumped to 0: Basis ADR:P0=0x40;P1=0x42;P2=0x44;P3=0x46;
+       //ADR-Jumper on IIC4xPCF8574board jumped to 1: Basis ADR:P0=0x48;P1=0x4A;P2=0x4C;P3=0x4E; 
+#define LED_MASK  0xffff    //Portc has 16bit, therefore 4digit mask
+                            // 1=output    0=input
+              
+I2C i2c(I2C_SDA, I2C_SCL); //IIC Pins SDA and SCL for ARDUINO pinheader Nucleo-board
+            //SCL and SPA pullup resistors 2k2Ohm to+5Volt
+            
+PortOut leds(PortC, LED_MASK); //Important: Port_B not possible -> PB_8 PB_9 Pins for IIC-bus
+            
+DigitalOut myled(LED1); //LED on Nucleo-board
+//for the task1****:  AnalogIn analog_value0(A0);      //same as Pin PA_0 
+//for the task2****:  Serial pc(SERIAL_TX, SERIAL_RX);
+ 
+int main()
+{
+    char input8bit;
+    char data_write[2]; //must be char!!
+    char data_read[2]; //read buffer
+ 
+    data_write[0] = 0xf2; //LEDs low aktiv  dummy
+    int status = i2c.write(PCF8574_ADDRoutput , data_write, 1, 0);
+    if (status != 0) // Error  no acknowledge detected 
+    { 
+        while (1) //-> endless loop when error no IIC-IC detected
+        {   
+        myled = !myled;
+        wait(0.7);
+        }
+    }
+ 
+    while (1) //endless loop
+        {
+ 
+        // i2c.read will start the IIC-bus with the last 0 also stop the same by 12c.read
+        i2c.read(PCF8574_ADDRinput, data_read, 1, 0);  // read to array  1byte  stop
+        input8bit = data_read[0];   //array value to variable
+        leds = input8bit; //Output PortC low-byte 
+        data_write[0] = input8bit;     //8bit analog-value to array
+        i2c.write(PCF8574_ADDRoutput , data_write, 1, 0); //  output array 1byte  stop 
+        //you see a digital 8bit PCF8574 output (8xleds), received from PCF8574 input (8xswitsches)
+        
+        //Here your solutions from task1 and 2:
+    }
+ 
+}
+