Digi International Inc. / Mbed 2 deprecated XBeeDM_modem_status

DigiMesh Modem Status example for mbed XBeeLib By Digi

Dependencies:   XBeeLib mbed

Fork of XBeeZB_modem_status by Digi International Inc.

Description

This example shows how to register a function callback to be aware of modem status changes. This library will call the registered callback whenever the XBee module radio modem changes its status

See Handling modem status changes chapter for more information.

Common Setup

Make sure you have a valid Example Common Setup

Example Setup

This example does not require any additional setup.

Running the example

Build and deploy the example to the mbed module.
Reset the mbed module so the example starts. You should see the example debug information through the debug interface configured in the 'Local Setup' chapter.

It you set up a network as described in the Common Setup section, you should see following modem status in the debug interface:

  • Modem Status 0x0: Corresponds to 'HwReset' meaning 'Hardware reset'

config.h

Committer:
hbujanda
Date:
2016-07-29
Revision:
10:47db8cbb2e2d
Parent:
6:a75fe0a5c249

File content as of revision 10:47db8cbb2e2d:

/**
 * Copyright (c) 2015 Digi International Inc.,
 * All rights not expressly granted are reserved.
 *
 * This Source Code Form is subject to the terms of the Mozilla Public
 * License, v. 2.0. If a copy of the MPL was not distributed with this file,
 * You can obtain one at http://mozilla.org/MPL/2.0/.
 *
 * Digi International Inc. 11001 Bren Road East, Minnetonka, MN 55343
 * =======================================================================
 */

#ifndef __CONFIG_H_
#define __CONFIG_H_

/** Library configuration options */
#define ENABLE_LOGGING
#define ENABLE_ASSERTIONS
#define FRAME_BUFFER_SIZE           4
#define MAX_FRAME_PAYLOAD_LEN       128

#define SYNC_OPS_TIMEOUT_MS         2000

//#define RADIO_TX                NC /* TODO: specify your setup's Serial TX pin connected to the XBee module DIN pin */
//#define RADIO_RX                NC /* TODO: specify your setup's Serial RX pin connected to the XBee module DOUT pin */
//#define RADIO_RTS               NC /* TODO: specify your setup's Serial RTS# pin connected to the XBee module RTS# pin */
//#define RADIO_CTS               NC /* TODO: specify your setup's Serial CTS# pin connected to the XBee module CTS# pin */
//#define RADIO_RESET             NC /* TODO: specify your setup's GPIO (output) connected to the XBee module's reset pin */
//#define RADIO_SLEEP_REQ         NC /* TODO: specify your setup's GPIO (output) connected to the XBee module's SLEEP_RQ pin */
//#define RADIO_ON_SLEEP          NC /* TODO: specify your setup's GPIO (input) connected to the XBee module's ON_SLEEP pin */
//#define DEBUG_TX                NC /* TODO: specify your setup's Serial TX for debugging */
//#define DEBUG_RX                NC /* TODO: specify your setup's Serial RX for debugging (optional) */

#if !defined(RADIO_TX)
    #error "Please define RADIO_TX pin"
#endif

#if !defined(RADIO_RX)
    #error "Please define RADIO_RX pin"
#endif

#if !defined(RADIO_RESET)
    #define RADIO_RESET             NC
    #warning "RADIO_RESET not defined, defaulted to 'NC'"
#endif

#if defined(ENABLE_LOGGING)
    #if !defined(DEBUG_TX)
        #error "Please define DEBUG_TX"
    #endif
    #if !defined(DEBUG_RX)
        #define DEBUG_RX                NC
        #warning "DEBUG_RX not defined, defaulted to 'NC'"
    #endif
#endif

#endif /* __CONFIG_H_ */