Digi International Inc. / Mbed 2 deprecated XBee802_Send_Data

802.15.4 Send Data example for mbed XBeeLib By Digi

Dependencies:   XBeeLib mbed

Description

This example shows how to send data to a remote XBee802 module. The application creates a message for a remote XBee module. This library encodes and sends it to the local XBee module through the serial port. Then the local XBee module sends the packet to the remote XBee module through the air.

The example shows how to send both unicast and broadcast messages.

See Sending data to another module chapter for more information.

Common Setup

Make sure you have a valid Example Common Setup

Example Setup

XBee modules

To evaluate the 16-bit addressing mode you have to configure the local XBee module and the remote XBee module with unique values... for example 0x1111 for the local and 0x2222 for the remote.

Application

Broadcast messages doesn't require any configuration, but for the unicast messages you have to configure:

  • The remote device 64-bit address by customizing the REMOTE_NODE_ADDR64_MSB and REMOTE_NODE_ADDR64_LSB defines with the remote XBee module 64-bit address.
  • The remote device 16-bit address by customizing the REMOTE_NODE_ADDR16 define with the remote XBee module 16-bit address.

Running the example

Build and deploy the example to the mbed module.
Reset the mbed module so the example starts. You should see the example debug information through the debug interface configured in the 'Local Setup' chapter. The application will first send a broadcast message and finally a couple of unicast messages to the configured remote XBee module (first using 64-bit addressing mode and then using 16-bit addressing mode).

Verify that the remote XBee module is receiving the frames by accessing the "Console" tab of the X-CTU. You should see there the broadcast and unicast messages.

config.h

Committer:
hbujanda
Date:
2016-07-29
Revision:
10:73901166c6f4
Parent:
7:ab86cae2e208

File content as of revision 10:73901166c6f4:

/**
 * Copyright (c) 2015 Digi International Inc.,
 * All rights not expressly granted are reserved.
 *
 * This Source Code Form is subject to the terms of the Mozilla Public
 * License, v. 2.0. If a copy of the MPL was not distributed with this file,
 * You can obtain one at http://mozilla.org/MPL/2.0/.
 *
 * Digi International Inc. 11001 Bren Road East, Minnetonka, MN 55343
 * =======================================================================
 */

#ifndef __CONFIG_H_
#define __CONFIG_H_

/** Library configuration options */
#define ENABLE_LOGGING
#define ENABLE_ASSERTIONS
#define FRAME_BUFFER_SIZE           4
#define MAX_FRAME_PAYLOAD_LEN       128

#define SYNC_OPS_TIMEOUT_MS         2000

//#define RADIO_TX                NC /* TODO: specify your setup's Serial TX pin connected to the XBee module DIN pin */
//#define RADIO_RX                NC /* TODO: specify your setup's Serial RX pin connected to the XBee module DOUT pin */
//#define RADIO_RTS               NC /* TODO: specify your setup's Serial RTS# pin connected to the XBee module RTS# pin */
//#define RADIO_CTS               NC /* TODO: specify your setup's Serial CTS# pin connected to the XBee module CTS# pin */
//#define RADIO_RESET             NC /* TODO: specify your setup's GPIO (output) connected to the XBee module's reset pin */
//#define RADIO_SLEEP_REQ         NC /* TODO: specify your setup's GPIO (output) connected to the XBee module's SLEEP_RQ pin */
//#define RADIO_ON_SLEEP          NC /* TODO: specify your setup's GPIO (input) connected to the XBee module's ON_SLEEP pin */
//#define DEBUG_TX                NC /* TODO: specify your setup's Serial TX for debugging */
//#define DEBUG_RX                NC /* TODO: specify your setup's Serial RX for debugging (optional) */

#if !defined(RADIO_TX)
    #error "Please define RADIO_TX pin"
#endif

#if !defined(RADIO_RX)
    #error "Please define RADIO_RX pin"
#endif

#if !defined(RADIO_RESET)
    #define RADIO_RESET             NC
    #warning "RADIO_RESET not defined, defaulted to 'NC'"
#endif

#if defined(ENABLE_LOGGING)
    #if !defined(DEBUG_TX)
        #error "Please define DEBUG_TX"
    #endif
    #if !defined(DEBUG_RX)
        #define DEBUG_RX                NC
        #warning "DEBUG_RX not defined, defaulted to 'NC'"
    #endif
#endif

#endif /* __CONFIG_H_ */