File content as of revision 24:7d2ff444d6d8:

//Libraries
#include "GSMLibrary.h"
#include "gsmqueue.h"
#include <string.h>

//Global defines
#define TIMEOUTLIMIT SECONDS_TIMEOUT/TIME_CONST //$change check with main code this will set up condition fior timeout.
#define BEGIN_PHOTODIODE_DATA "CLS:"
#define BEGIN_GPS_DATA "GPS:"

//Extra defines for transmitter
#define START_SMS_TRANSMISSION "START"
#define STOP_SMS_TRANSMISSION "STOP"
#define GPS_SMS_TRANSMISSION "GPS"
#define RECEIVER_PHONE_NUMBER "\"+13853357314\""
#define AT_CMGS "AT+CMGS=" RECEIVER_PHONE_NUMBER
#define NUM_SIZE 25

//definition for AT comands to send
#define AT_OK "AT"
#define AT_CSQ "AT+CSQ" 
#define AT_CREG "AT+CREG?"
#define AT_CNMI "AT+CNMI=2,0,0,0,0"
#define AT_CMGF "AT+CMGF=1"
#define AT_READ_MSG "AT+CMGL=\"REC UNREAD\"" //make sure device is in txt mode.
#define AT_DEL_R_MSGS "AT+QMGDA=\"DEL READ\""

//Definition for AT responses
//Please notice that after ":" the gsm will usually send aditional information
#define AT_OK_RESPONSE "OK" //Response after sending "AT" message
#define AT_CSQ_RESPONSE "+CSQ:" //+CSQ: <arg1>,<arg2> where <arg1> is signal strength arg1 = 0-30 where a number below 10 means low signal strength and 99 is not knwn or detectable signal and arg2 is bit error rate form 0-7, 99 will represent error 
#define AT_CREG_RESPONSE "+CREG:"//+CREG: <arg1>,<arg2> where <arg1> = 0-2(see AT command descriptions), <arg2> =  0-5, 0 not registered to nework and not looking for one. 1 is conected to network, 2 is not conected but searching
#define AT_CNMI_RESPONSE "OK"
#define AT_CMGF_RESPONSE "OK"
#define AT_CMGS_RESPONSE ">"  //Received after you give the GSM the phone number. (We mistakenly thought it was received a second time after SMS was sent... this is not true!)
#define AT_SENDSMS_RESPONSE "+CMGS:" // +CMGS: <id> this will include the message id. CMS ERROR for error.
#define AT_DEL_R_MSGS_RESPONSE "OK"

//External variables
extern Serial pc;
extern Serial gsm;
extern uint8_t buffer[BUFFER_LENGTH];//buffer storing char

//Internal variables
gsm_states gsm_current_state = GSM_INITIALIZE;
int timeout_count = 0;
char state_chars[] = "iosntmRPWD";  //init, ok, signalstrength, network, turn off notifications, messagemode, read, phone, writesms, del

//Extras for transmitter
char send = false;  //if true => we will send something (only if send_enable is true)
char send_enable = false;   //Sending start and stop commands to GSM via SMS changes this variable
char undeleted_msgs = true; //At the beginning assume we have undeleted messages
char gsm_msg[MAX_SMS_LENGTH + 250]; //String storing SMS message to send to GSMMaximum (add 250 length to give leeway)
char num[NUM_SIZE];   //Temporary string storage to convert numbers

void gsm_tick()
{

    if (queueHasResponse() || gsm_timeOut() || gsm_current_state == GSM_INITIALIZE)
    {
        gsm_printState();   //&debug
        printQueue();   //&debug
        gsm_nextStateLogic();   //Next state
        gsm_mealyOutputs(); //Mealy outputs
    }
}
 
void gsm_printState()
{
    pc.printf("S:%c;", state_chars[gsm_current_state]);
}
 
//Advance timeout counter; if timeout, return true
bool gsm_timeOut()
{
    if(++timeout_count >= TIMEOUTLIMIT){
        timeout_count = 0; 
        gsm_reset();
        return true;
    }
    else
        return false;     
}

//Have the GSM send data - L = long, S = short, hh/mm/ss for time, "lat ns" for latitute, "lon we" for longitude
void gsm_send_data(float L, float Lref, float S, float Sref, int hh, int mm, int ss, float lat, char ns, float lon, char we)
{
    if (!gsm_ready())   //Don't send if gsm not ready
        return;
    
    //Concatenate photodiode data
    gsm_msg[0] = NULL;
    strcat(gsm_msg, BEGIN_PHOTODIODE_DATA);
    snprintf(num, NUM_SIZE, ",%d:%d:%d,", hh, mm, ss);
    strcat(gsm_msg, num);
    snprintf(num, NUM_SIZE, "%f,", L);
    strcat(gsm_msg, num);
    snprintf(num, NUM_SIZE, "%f,", Lref);
    strcat(gsm_msg, num);
    snprintf(num, NUM_SIZE, "%f,", S);
    strcat(gsm_msg, num);
    snprintf(num, NUM_SIZE, "%f;\n", Sref);
    strcat(gsm_msg, num);

    //Concatenate gps data
    strcat(gsm_msg, BEGIN_GPS_DATA);
    if (ns != NULL) //If there is a gps fix, ns will be set
    { 
        snprintf(num, NUM_SIZE, ",%.4f%c,%.4f%c;", lat, ns, lon, we);
        strcat(gsm_msg, num);
    }
        else strcat(gsm_msg, ",NONE;");
    
    send = true;    //Mark that we are currently sending a message
    strcat(gsm_msg, SMS_END_CHAR);  //Add SMS end char
}
 
//Return true if gsm is ready to send sms
//This only occurs if send = false (not currently sending a message) AND gsm received start sequence
bool gsm_ready()
{
    return ((!send) && send_enable) ? true : false;
}
 
//Reset the gsm. Currently this only resets the state and whether we are currently sending a message
//It does not reset send_enable or undeleted_msgs
void gsm_reset()
{
    //If we are in the middle of sending a text message, exit this loop
    if (gsm_current_state == GSM_AT_CMGS)
        sendCommand(SMS_ESCAPE_CHAR);
    
    gsm_current_state = GSM_INITIALIZE;
    undeleted_msgs = true;
    send = false;
}
 
//Next state logic -----------------------------------------------------
void gsm_nextStateLogic()
{
    //printQueue(); //$debug
 
    switch(gsm_current_state)
    {
        case GSM_INITIALIZE:
            timeout_count = 0;
            gsm_current_state = GSM_AT_OK;   //unconditional (check it)
            break;
        case GSM_AT_OK:
            if (findInQueue(AT_OK_RESPONSE, true))
                gsm_current_state = GSM_AT_CSQ;
            break;
        case GSM_AT_CSQ:
            if(findInQueue(AT_CSQ_RESPONSE, true))
                gsm_current_state = GSM_AT_CREG;
            break;
        case GSM_AT_CREG:
            if(findInQueue(AT_CREG_RESPONSE, true))
            {
                parseInt();
                if(parseInt() == 1)
                    gsm_current_state = GSM_AT_CNMI;
            } 
            break;
        case GSM_AT_CNMI:
            if(findInQueue(AT_CNMI_RESPONSE, true))
                gsm_current_state = GSM_AT_CMGF;
            break;  
        case GSM_AT_CMGF:
            if(findInQueue(AT_CMGF_RESPONSE, true))
                gsm_current_state = GSM_READ_MSG;
            break;
        case GSM_READ_MSG:
            if(send_enable) //Check if we need to stop transmission of SMS
            {
                if(findInQueue(STOP_SMS_TRANSMISSION, true))  //Always stop sending if stop sequence received by SMS
                {
                    undeleted_msgs = true;
                    send_enable = false;    //Set send_enable to indicate we will stop sending SMS
                }
                else if (send) //Only continue sending if we didn't find stop sequence AND user requested that we send sms
                    gsm_current_state = GSM_AT_CMGS;    //Continue sending SMS (change state accordingly)
                //Implicit: otherwise we will continue checking text messages in this state.
            }
            else
            {
                if(findInQueue(START_SMS_TRANSMISSION, true))
                {
                    undeleted_msgs = true;
                    send_enable = true;
                    if (send) //Only continue sending if we found start sequence AND user requested that we send sms
                        gsm_current_state = GSM_AT_CMGS;    //Start sending SMS (change state accordingly)
                }
            }
            break;
        case GSM_AT_CMGS:
            if(findInQueue(AT_CMGS_RESPONSE, true))
                gsm_current_state = GSM_AT_SENDSMS;
            break;
        case GSM_AT_SENDSMS:
            if(findInQueue(AT_SENDSMS_RESPONSE, true))
            {
                pc.printf("(Wid%i)",parseInt());//&debug
                timeout_count = 0;  //Reset timeout count
                send = 0;   //Indicate we are done sending the text message
                if (undeleted_msgs) //Check if we need to delete read messages
                    gsm_current_state = GSM_DEL_R_MSGS; //Only delete messages if there are no unread messages
                else
                {
                    gsm_current_state = GSM_READ_MSG;   //Otherwise read text messages again
                    pc.printf("(Dnone)");//&debug 
                }
            }
            else
            {
                pc.printf("(Werr)"); //&debug
                gsm_current_state = GSM_AT_CMGS;    //If failed, try resending the message (i.e. continue until timeout)
            }
            break;
        case GSM_DEL_R_MSGS:
            if (findInQueue(AT_DEL_R_MSGS_RESPONSE, true))
            {
                undeleted_msgs = false;
                pc.printf("(Dsucc)");   //&debug
            }
            else
                pc.printf("(Derr)");    //&debug
            gsm_current_state = GSM_READ_MSG;
            break;
        default:
            pc.printf("This is a state error\r\n");
    }
}
 
//Mealy output logic ------------------------------------------------------
void gsm_mealyOutputs()
{
    switch(gsm_current_state)
    {
        case GSM_INITIALIZE:
            break;
        case GSM_AT_OK:
            sendCommand(AT_OK);
            break;
        case GSM_AT_CSQ:
            sendCommand(AT_CSQ);
            break;
        case GSM_AT_CREG:
            sendCommand(AT_CREG);
            break;
        case GSM_AT_CNMI:
            sendCommand(AT_CNMI);
            break; 
        case GSM_AT_CMGF:
            sendCommand(AT_CMGF);
            break;         
        case GSM_READ_MSG:
            sendCommand(AT_READ_MSG);
            break; 
        case GSM_AT_CMGS:   
            sendCommand(AT_CMGS);
            break;
        case GSM_AT_SENDSMS:
            sendCommand(gsm_msg); //end char included
            break;
        case GSM_DEL_R_MSGS:
            sendCommand(AT_DEL_R_MSGS);
            break;
        default:
            pc.printf("This is a state error\r\n");
    }
}
//Initialize the GSM
void gsm_initialize(){  
      SIM_SCGC6 |= SIM_SCGC6_DMAMUX_MASK; //enabling dmamux clock
      SIM_SCGC7 |= SIM_SCGC7_DMA_MASK;  // enebaling dma clock
      pc.printf("initializing DMA...\r\n");
     // control register mux, enabling uart3 receive        
     DMAMUX_CHCFG0 |= DMAMUX_CHCFG_ENBL_MASK|DMAMUX_CHCFG_SOURCE(8); 
     
     // Enable request signal for channel 0 
     DMA_ERQ = DMA_ERQ_ERQ0_MASK;
     
      // select round-robin arbitration priority
     DMA_CR |= DMA_CR_ERCA_MASK;
     
     //enabled error interrupt for DMA0
     //DMA_EEI = DMA_EEI_EEI0_MASK ;
     //Addres for buffer
     DMA_TCD0_SADDR = (uint32_t) &UART_D_REG(UART3_BASE_PTR);
     DMA_TCD0_DADDR = (uint32_t) buffer;
     // Set an offset for source and destination address
     DMA_TCD0_SOFF = 0x00; 
     DMA_TCD0_DOFF = 0x01; // Destination address offset of 1 byte per transaction
     
     // Set source and destination data transfer size
     DMA_TCD0_ATTR = DMA_ATTR_SSIZE(0) | DMA_ATTR_DSIZE(0);
     
     // Number of bytes to be transfered in each service request of the channel
     DMA_TCD0_NBYTES_MLNO = 0x01;
     // Current major iteration count
    DMA_TCD0_CITER_ELINKNO = DMA_CITER_ELINKNO_CITER(BUFFER_LENGTH);
    DMA_TCD0_BITER_ELINKNO = DMA_BITER_ELINKNO_BITER(BUFFER_LENGTH);
    // Adjustment value used to restore the source and destiny address to the initial value
    // After reading 'len' number of times, the DMA goes back to the beginning by subtracting len*2 from the address (going back to the original address)
    DMA_TCD0_SLAST = 0;   // Source address adjustment
    DMA_TCD0_DLASTSGA = -BUFFER_LENGTH;  // Destination address adjustment   
    // Setup control and status register
    DMA_TCD0_CSR = 0;
       
    // enable interrupt call at end of major loop
    DMA_TCD0_CSR |= DMA_CSR_INTMAJOR_MASK;
    
    //Activate dma trasnfer rx interrupt
    UART_C2_REG(UART3) |= UART_C2_RIE_MASK;
    UART_C5_REG(UART3) |= UART_C5_RDMAS_MASK | UART_C5_ILDMAS_MASK | UART_C5_LBKDDMAS_MASK;
    //activate p fifo   
    UART_PFIFO_REG(UART3) |= UART_PFIFO_RXFE_MASK; //RXFE and buffer size of 1 word
    queueInit();
    pc.printf("done...\n\r");
}
 
 
 
//initialization debuging purposes
void print_registers() {
    
   
    pc.printf("\n\rDMA REGISTERS\n\r");
    pc.printf("DMA_MUX: 0x%08x\r\n",DMAMUX_CHCFG0);
    pc.printf("SADDR0: 0x%08x\r\n",DMA_TCD0_SADDR);
    pc.printf("DADDR0: 0x%08x\r\n",DMA_TCD0_DADDR);
    pc.printf("CITER0: 0x%08x\r\n",DMA_TCD0_CITER_ELINKNO);
    pc.printf("BITER0: 0x%08x\r\n",DMA_TCD0_BITER_ELINKNO);
    pc.printf("DMA_CR: %08x\r\n", DMA_CR);
    pc.printf("DMA_ES: %08x\r\n", DMA_ES);
    pc.printf("DMA_ERQ: %08x\r\n", DMA_ERQ);
    pc.printf("DMA_EEI: %08x\r\n", DMA_EEI);
    pc.printf("DMA_CEEI: %02x\r\n", DMA_CEEI);
    pc.printf("DMA_SEEI: %02x\r\n", DMA_SEEI);
    pc.printf("DMA_CERQ: %02x\r\n", DMA_CERQ);
    pc.printf("DMA_SERQ: %02x\r\n", DMA_SERQ);
    pc.printf("DMA_CDNE: %02x\r\n", DMA_CDNE);
    pc.printf("DMA_SSRT: %02x\r\n", DMA_SSRT);
    pc.printf("DMA_CERR: %02x\r\n", DMA_CERR);
    pc.printf("DMA_CINT: %02x\r\n", DMA_CINT);
    pc.printf("DMA_INT: %08x\r\n", DMA_INT);
    pc.printf("DMA_ERR: %08x\r\n", DMA_ERR);
    pc.printf("DMA_HRS: %08x\r\n", DMA_HRS);
    pc.printf("DMA_TCD0_DOFF: %08x\r\n",DMA_TCD0_DOFF);
    pc.printf("\n\rUART REGISTERS\n\r");
    pc.printf("UART_BDH_REG: %08x\r\n",UART_BDH_REG(UART3)); 
    pc.printf("UART_C1_REG: %08x\r\n",UART_C1_REG(UART3));
    pc.printf("UART_C2_REG: %08x\r\n",UART_C2_REG(UART3));
    pc.printf("UART_S1_REG: %08x\r\n",UART_S1_REG(UART3));
    pc.printf("UART_s2_REG: %08x\r\n",UART_S2_REG(UART3));  
    pc.printf("UART_C3_REG: %08x\r\n",UART_C3_REG(UART3));
    pc.printf("UART_D_REG: %08x\r\n",UART_D_REG(UART3));
    pc.printf("UART_MA1_REG: %08x\r\n",UART_MA1_REG(UART3));
    pc.printf("UART_MA2_REG: %08x\r\n",UART_MA2_REG(UART3));
    pc.printf("UART_C4_REG: %08x\r\n",UART_C4_REG(UART3));
    pc.printf("UART_C5_REG: %08x\r\n",UART_C5_REG(UART3));
    pc.printf("UART_ED_REG: %08x\r\n",UART_ED_REG(UART3));   
    pc.printf("UART_MODEM_REG: %08x\r\n",UART_MODEM_REG(UART3));
    pc.printf("UART_IR_REG: %08x\r\n",UART_IR_REG(UART3)); 
    pc.printf("UART_PFIFO_REG: %08x\r\n",UART_PFIFO_REG(UART3));
    pc.printf("UART_CFIFO_REG: %08x\r\n",UART_CFIFO_REG(UART3));
    pc.printf("UART_SFIFO_REG: %08x\r\n",UART_SFIFO_REG(UART3)); 
    pc.printf("UART_TWFIFO_REG: %08x\r\n",UART_TWFIFO_REG(UART3));
    pc.printf("UART_TCFIFO_REG: %08x\r\n",UART_TCFIFO_REG(UART3)); 
    pc.printf("UART_RWFIFO_REG: %08x\r\n",UART_RWFIFO_REG(UART3)); 
    pc.printf("UART_RCFIFO_REG: %08x\r\n",UART_RCFIFO_REG(UART3));
  
}