Diff: main.cpp

Revision:

6:96de1304b9e7

Parent:

5:44f7dbc5c75d

diff -r 44f7dbc5c75d -r 96de1304b9e7 main.cpp
--- a/main.cpp	Fri May 01 14:31:45 2020 +0000
+++ b/main.cpp	Fri May 29 11:28:45 2020 +0000
@@ -1,61 +1,199 @@
 #include "mbed.h"
 #include "iAQ_Core.h"
-
-iAQ_Core myiAQ_Core ( PB_11,PB_10, iAQ_Core::iAQ_Core_ADDRESS );
+#include "Adafruit_SGP30.h"
+#include"BME680.h"
+BME680 myBME680     ( PC_1,PC_0, 400000 ); //BME680
+iAQ_Core myiAQ_Core ( PB_11_ALT0,PB_10_ALT0, iAQ_Core::iAQ_Core_ADDRESS ); //iAQ-Core C
+Adafruit_SGP30 sgp30(PB_14,PB_13); // SGP30    
+I2C ZMODtemp(PB_9, PB_8); //ZMOD and Si7050
 Serial ble(PC_12,PD_2);
 
-Ticker      newReading;
-
 iAQ_Core::iAQ_Core_status_t  aux;
 iAQ_Core::iAQ_Core_data_t    myiAQ_Core_data;
-uint32_t                     myState = 0;
+
+///BME680 EXTRA FUNCTIONS///
+Ticker      newReading;
+
+uint32_t    myState = 0;
 
+//@brief   FUNCTION PROTOTYPES
+void    changeDATA     ( void );
+void    user_delay_ms  ( uint32_t  period );
+int8_t  user_i2c_read  ( uint8_t dev_id, uint8_t reg_addr, uint8_t *reg_data, uint16_t len );
+int8_t  user_i2c_write ( uint8_t dev_id, uint8_t reg_addr, uint8_t *reg_data, uint16_t len );
 
 void changeDATA ( void )
 {
     myState = 1;
 }
 
+void user_delay_ms ( uint32_t period )
+{
+    wait( 0.01 );
+}
 
-int main()
+int8_t user_i2c_read ( uint8_t dev_id, uint8_t reg_addr, uint8_t *reg_data, uint16_t len )
 {
-    ble.baud(9600);
-    
-    uint32_t myWarmUpCounter  =   0;
+    int8_t rslt = 0; // Return 0 for Success, non-zero for failure
+
+    uint32_t aux     =   0;
+    aux      =   myBME680._i2c.write ( dev_id, (char*)&reg_addr, 1, true );
+    aux      =   myBME680._i2c.read  ( dev_id, (char*)&reg_data[0], len );
+
+
+
+    if ( aux == 0 ) {
+        rslt     =   0;
+    } else {
+        rslt     =   0xFF;
+    }
+
+
+    return rslt;
+}
+
+int8_t user_i2c_write ( uint8_t dev_id, uint8_t reg_addr, uint8_t *reg_data, uint16_t len )
+{
+    int8_t rslt = 0; // Return 0 for Success, non-zero for failure
+
+    uint32_t     aux     =   0;
+    char         cmd[16] =  { 0 };
+    uint32_t     i       =   0;
+
+    // Prepare the data to be sent
+    cmd[0]   =   reg_addr;
+    for ( i = 1; i <= len; i++ ) {
+        cmd[i]   =   reg_data[i - 1];
+    }
+
+    // Write data
+    aux      =   myBME680._i2c.write ( dev_id, &cmd[0], len + 1, false );
 
 
 
-    // iAQ-Core warm up is at least 5 minutes ( 300 * 1s ) or when the sensor is ready
-    do
-    {
-      aux      =   myiAQ_Core.iAQ_Core_GetNewReading ( &myiAQ_Core_data );
-      wait(1);
-      myWarmUpCounter++;
-    } while( ( myWarmUpCounter < 300 ) && ( myiAQ_Core_data.status == iAQ_Core::iAQ_Core_STATUS_RUNIN ) );
+    if ( aux == 0 ) {
+        rslt     =   0;
+    } else {
+        rslt     =   0xFF;
+    }
+
+
+    return rslt;
+}
 
 
-    newReading.attach( &changeDATA, 0.1);                                        // the address of the function to be attached ( changeDATA ) and the interval ( 1s )
+int main()
+{
+    ble.baud(115200); //baudrate for the serial connection, 9600 for hc05 115200 for rn
 
-    // Let the callbacks take care of everything
-    while(1)
-    {
-      sleep();
+    ble.printf("$");//enter command mode only for rn
+    wait(0.1);
+    ble.printf("$$");//enter command mode
+    wait(0.5);
+    ble.printf("SN,Testing 1 2 1 2 \r");//set new name
+    wait(0.5);
+    ble.printf("SS,C0\r");//set transparent uart
+    wait(0.5);
+    ble.printf("&,50278635E070\r");//Assign mac
+    wait(0.5);
+    ble.printf("---\r");//enter data mode
+    wait(0.5);
+    
+    ///IAQ DOESN'T REQUIRE INITIALISATION///
+    
+    ///SGP30///
+    sgp30.begin();//begin sgp30
+    sgp30.IAQinit();//initialise sgp30
+    
+    
+    
+    ///BME680//
+    struct bme680_dev gas_sensor;
+
+    gas_sensor.dev_id   =   BME680_I2C_ADDR_PRIMARY;
+    gas_sensor.intf     =   BME680_I2C_INTF;
+    gas_sensor.read     =   user_i2c_read;
+    gas_sensor.write    =   user_i2c_write;
+    gas_sensor.delay_ms =   user_delay_ms;
+    // amb_temp can be set to 25 prior to configuring the gas sensor
+    // or by performing a few temperature readings without operating the gas sensor.
+    gas_sensor.amb_temp =   25;
+
+
+    int8_t rslt = BME680_OK;
+    rslt = myBME680.bme680_init ( &gas_sensor );
 
 
+    uint8_t set_required_settings;
 
-      if ( myState == 1 ) {
-        // New reading
-        do {
-            aux      =   myiAQ_Core.iAQ_Core_GetNewReading (  &myiAQ_Core_data );
-            wait_ms(1);
-        } while( myiAQ_Core_data.status != iAQ_Core::iAQ_Core_STATUS_OK );          // [TODO] Dangerous!!! The uC may get stuck here if something goes wrong!
-                                                                                    // [WORKAROUND] Insert a counter.
+    // Set the temperature, pressure and humidity settings
+    gas_sensor.tph_sett.os_hum  = BME680_OS_2X;
+    gas_sensor.tph_sett.os_pres = BME680_OS_4X;
+    gas_sensor.tph_sett.os_temp = BME680_OS_8X;
+    gas_sensor.tph_sett.filter  = BME680_FILTER_SIZE_3;
+
+    // Set the remaining gas sensor settings and link the heating profile
+    gas_sensor.gas_sett.run_gas = BME680_ENABLE_GAS_MEAS;
+    // Create a ramp heat waveform in 3 steps
+    gas_sensor.gas_sett.heatr_temp  = 320; // degree Celsius
+    gas_sensor.gas_sett.heatr_dur   = 150; // milliseconds
+
+    // Select the power mode
+    // Must be set before writing the sensor configuration
+    gas_sensor.power_mode = BME680_FORCED_MODE;
+
+    // Set the required sensor settings needed
+    set_required_settings = BME680_OST_SEL | BME680_OSP_SEL | BME680_OSH_SEL | BME680_FILTER_SEL | BME680_GAS_SENSOR_SEL;
+
+    // Set the desired sensor configuration
+    rslt = myBME680.bme680_set_sensor_settings ( set_required_settings, &gas_sensor );
+
+    // Set the power mode
+    rslt = myBME680.bme680_set_sensor_mode ( &gas_sensor );
+
+
+    // Get the total measurement duration so as to sleep or wait till the measurement is complete
+    uint16_t meas_period;
+    myBME680.bme680_get_profile_dur ( &meas_period, &gas_sensor );
+
+    struct bme680_field_data data;
+
 
-        // Send data through the UART
-        ble.printf( "Pred: %d | Tvoc: %d | Resistance: %d\r\n", myiAQ_Core_data.pred, myiAQ_Core_data.Tvoc, myiAQ_Core_data.resistance );
-        wait(0.01);
-        myState  =   0;                                                             // Reset the variable
+    newReading.attach( &changeDATA, 1 );                                        // the address of the function to be attached ( changeDATA ) and the interval ( 1s )
+    
+    //END BME680///
+    
+    ///ZMOD AND TEMP///
+    int ZMODTEMPaddr=0x80; //si7050 8bit address
+    
+    char wTemp[1];
+    wTemp[0]=0xE3; //Hold master mode
+    char rTemp[2]; //Temperature returns MSB and LSB
+                    //assume MBS in rTemp[0] and LSB in rTemp[1]
+    
+    char wInit[2];
+    wInit[0]=0xE6; //User register 1
+    wInit[1]=0x00; //Set 14 bit resolution, other read-ony registers shouldn't be affected
+    
+    ZMODtemp.write(ZMODTEMPaddr,wInit,2);
+    ///END ZMOD AND TEMP///
+    
+    while(1)
+    {
+        myiAQ_Core.iAQ_Core_GetNewReading (  &myiAQ_Core_data ); //Measurement from iAQ-Core C
+        wait(0.1);
+        sgp30.IAQmeasure();//Measurement from SGP30
+        
+        rslt = myBME680.bme680_get_sensor_data ( &data, &gas_sensor ); //Measurement for BME680
+        
+        ZMODtemp.write(ZMODTEMPaddr,wInit,2); //maybe?
+        ZMODtemp.write(ZMODTEMPaddr,wTemp,1);
+        ZMODtemp.read(ZMODTEMPaddr,rTemp,2); //Returns 2 bytes
+        float temp_code=(rTemp[0]<<8)+rTemp[1];
+        float SiTemp=((175.72*temp_code)/65536)-46.85;
+        
+        ble.printf( "iAQ CO2: %d, iAQ VOC: %d, iAQ Resistance: %d, SGP30 CO2: %d, SGP30 VOC: %d, BME680 Res: %d, BME680 Temp: %.2f, BME680 Hum: %.2f, BME680 Pres: %.2f, Si7051 temp: %.2f\r\n", myiAQ_Core_data.pred, myiAQ_Core_data.Tvoc, myiAQ_Core_data.resistance, sgp30.eCO2,sgp30.TVOC, data.gas_resistance ,( data.temperature/100.0f ) , ( data.humidity / 1000.0f ), ( data.pressure / 100.0f ) , SiTemp );  //Real results after 5 minutes of ON time
+    
+        rslt = myBME680.bme680_set_sensor_mode ( &gas_sensor ); //BME680 reset
       }
-
-    }
 }
\ No newline at end of file